ChrisMoody

CM Willams %R and CCI BackGround Highlight

CM_Willams %R and CCI BackGround Highlight

Created By User Request

Indicator Highlights:

Creates Red BackGround Highlight if CCI Or Williams %R are Above Upper Line (User Defined)

Creates Green BackGround Highlight if CCI Or Williams %R are Below Lower Line (User Defined)

Ability to Turn On/Off either Williams %R or CCI Highlights in Inputs Tab via Check Boxes.

Ability To Set All Parameters for CCI and Williams %R in Inputs Tab.

Ability to Set High/Low “Threshold” Lines for Both CCI and Williams %R in Inputs Tab.

***I was asked if you could plot Back Ground Highlights on Two Individual Indicators AND have it show if BOTH Indicators were Overbought and Oversold.
***The answer is Yes. On the Chart Above I have the same Shade of Red and Green for Both Indicators. However, you will notice when Both Indicators Show OverBought…Both Plot Red Back Ground Highlights Which = a Brighter Red. The same is True for Oversold Conditions. The Green Shows a Brighter Shade of Green.

***VERY IMPORTANT - It is difficult for a programmer to release Indicators with this feature because depending on what color background you use on your charts…THE COLORS LOOK COMPLETELY DIFFERENT. So If You Don’t Use The Black Back Ground Shown Above You Most Likely Will Need To Adjust The Transparency, and Possibly The Colors Themselves!!!!

Reference Page
http://www.tradingview.com/v/UmsFo3hv/

開源腳本

本著真正的TradingView精神,該腳本的作者將其開源發布,以便交易者可以理解和驗證它。為作者喝彩吧!您可以免費使用它,但在出版物中重複使用此代碼受網站規則的約束。 您可以收藏它以在圖表上使用。

免責聲明

這些資訊和出版物並不意味著也不構成TradingView提供或認可的金融、投資、交易或其他類型的意見或建議。請在使用條款閱讀更多資訊。

想在圖表上使用此腳本?
//Created by ChrisMoody on 10-17-2014 by user request.

study(title="CM_Willams %R and CCI BackGround Highlight", shorttitle="CM_%R and CCI", overlay=true)
length = input(21, minval=1, title="Williams %R Length")
willTL = input(10, minval=5, maxval=95, title="Williams %R Trigger Lines, 20 Converts to -20,-80...10 = -10,-90 etc.")
length2 = input(30, minval=1, title="CCI Length")
cciT = input(200, minval=50, maxval=200, title="CCI Trigger Lines, Converts to +100,-100 - +200,-200 etc.")
scci = input(true, title="Show CCI BackGround Highlight")
swill = input(true, title="Show Williams %R BackGround Highlight")
//CCI Code
ma = sma(close, length2)
cci = (close - ma) / (0.015 * dev(close, length2))
cciTA = 0 + cciT
cciTB = 0 - cciT
//CCI Criteria Definitions
cciA = cci > cciTA ? 1 : 0
cciB = cci < cciTB ? 1 : 0
//CCI Color Plots
condCCI = scci and cciA ? red : scci and cciB ? lime : na 
//Williams %R Definitions
upper = highest(length)
lower = lowest(length)
//Williams %R Criteria
willR = 100 * (close - upper) / (upper - lower)
willRAbove = willR > (0 - willTL) ? 1 : 0
willRBelow = willR < (-100 + willTL) ? 1 : 0
//Williams %R Color Definitions
condWill = swill and willRAbove ? red : swill and willRBelow ? lime : na

//Background Highlights
bgcolor(condCCI, transp=70)
bgcolor(condWill, transp=70)